Burst-electronics LG-1 User Manual

LG-1+ LG-4 Logo Generators Manual Version 2.01 BURST ELECTRONICS INC CORRALES, NM 87048 USA (505) 898-1455 VOICE (505) 890-8926 TECH SUPPORT (

Browse to the CD-ROM drive that has the LG Installation Disk. Select D:\Serial Bridge\FTDIPORT.INF and click Open (see Figure USB12). (Figure USB12)

A warning window stating that this driver has not passed Windows Logo testing will appear, just click on Continue Anyway (see Figure USB14). (Figure

Windows 98/ME Software Installation Insert the Program Files disk into your CD-ROM drive. If Windows does not automatically run the installation prog

(Figure 1) File Menu The FILE Menu contains the links for sending and saving logos to the LG hardware. Also, saving a logo from the LG hardware is l

Open Logo File Download Logo to RAM Save Current Settings in LG NVRAM Save Logo in NVRAM Upload Selected Logo From LG-4 (History) Exit Open Logo File

lost. Upload Selected Logo From LG-4 The Upload Selected Logo From LG-4 link is a feature that is only supported with the LG-4 family of logo generat

ZOOM Menu The Zoom Menu link does just what the name implies. Upon clicking the link, the currently selected logo will appear much larger within LOGO

Logo Menu The Logo Menu contains links for selecting a stored logo (LG-4 only) and links that enable the Relative Screen Position’s logo emulator. Th

Show Mix With this link checked, the logo displayed on the Relative Screen Position will change it’s Mix Ratio (transparency) as the Mix Ratio Slider

Schedule View (See Figure 7) Schedule allows a user to setup a sequence of times when a logo would be displayed. Select Schedule View. Within Schedul

Introduction Congratulations on your purchase of the Burst Electronics model LG family of logo generators. We hope that this manual will cover any q

End Slider – Tells LOGOGEN at what time a logo cycle will stop. The LOGO field to the right side of this table allows the user to select which logo wi

Tools have been selected, Diag appears between Schedule and Help on the main menu bar (See Figure 8). (Figure 8) Toggle Take – Toggles a logo between

numeric value from 0 – 99. 0 places the logo to the far left, and 99 places the logo to the far right. Vert Posn - a pop-up window prompting for a num

to be saved to disk. Click the Retrieve Logo command. Windows will then pop-up a Save As dialog box. In this window, the user is prompted for a file n

Manual – Is a link to the current version of the LG manual. This file is in PDF format and requires Adobe Acrobat Reader 4.0 or above to view. If you

Relative Screen Position The Relative Screen Position (RSP) in LOGOGEN gives an approximation of how a logo will appear on a video monitor. Features

about 5 seconds, fully right fades at about 0.05 seconds. Mix Ratio – A slider bar to change the transparency of a displayed logo. Fully left is trans

LG – Hardware This section of the manual will cover the appearance, connections and operation of the LG model family of logo generators. Position, Mi

the switch down causes the logo to be more transparent. Speed – Adjusts the rate at which a logo will transition between on and off when a Take funct

being displayed, LED off and the logo is not being displayed). Lock – This is a LED that indicates if the LG hardware is able to lock the logo image

Ability to retrieve a logo stored within the LG hardware. A link to the user’s manual within Help. Search for available COM ports. Product Descriptio

USB – (Future version of the LG-1+) Single USB2.0 compatible port. This port will take the place of the RS232 port currently used in the LG-1+. Video

Speed – Adjusts the rate at which the currently selected logo will transition between on and off when a Take function is performed. Pulling the switc

Logo 1-4 – These four LEDs indicate the currently selected logo. Use Select to cycle through each memory location where an individual logo is stored.

GPI – A RCA connector used to toggle a logo on and off. This connector uses a momentary contact closure between the center conductor and the sleeve to

If using Microsoft Paint (Paintbrush) to create a logo, the size and color settings must be set. This is accomplished by clicking on Image from the Pa

(Figure 15) When finished creating the logo, save the image and close Paint. The logo is now ready to be imported into LOGOGEN (see Open Logo File).

Specifications Power: 9 to 15 volts DC at 280mA (Polarity insensitive) or via 120 vol

FAQ Q: I send a logo to the LG-1+/LG-4, but when I cycle power, my new logo is not shown. A: Download your logo to RAM. Once the transfer is complet

Q: Why can’t I get my color logo installed into the LG hardware. A: The LG-1+ and LG-4 logo generators currently will only accept a monochrome bitmap

LG-1+ and LG-4 Logo Generators 38

Connect a video source to the Video In of the LG and connect Video Out to your monitor. Video will pass through the LG without power applied. Plug in

The Found New Hardware Wizard pops up next. Click on Install from a list or specific location (Advanced). Click Next. (see Figure USB2) (Figure USB2)

The next window asks for the location of the driver. Click on Browse (see Figure USB4) (Figure USB4) Browse to the CD-ROM drive that has the LG Insta

The next window asks the user to select compatible hardware. Select USB High Speed Serial Converter and click Next (see Figure USB6). (Figure USB6)

Click Finish on the Completing the Found New Hardware Wizard (see Figure USB8). (Figure USB8) Windows will now show another Found New Hardware; USB S

Windows will then restart the Found New Hardware Wizard. Select Install from a list or specific location. Click Next (see Figure USB10). (Figure USB10